Electric Power Gel Lead Acid Battery 6V 100AH High Performance
|Nominal Voltage||6V||Capacity||C10||100Ah (5.25V, at 25℃)|
|Nominal Capacity (C10)||100Ah (5.25V,at 25℃)||C5||80Ah (5.25V, at 25℃)|
|Dimension||Length 195mm||C3||75Ah (5.25V, at 25℃)|
|Width 170mm||C1||55Ah (5.1V, at 25℃)|
|Height 206mm||Internal Resistance||Approx. 1.65 mΩ (25℃)|
|Total Height 210mm||Max Short-duration Discharge Current||2000A(25℃)|
● Designed life for floating charge is 5 years (20℃);
● Design with flat plate, GEL electrolyte and AGM separator
● GEL electrolyte inside of battery keeps uniformity condition,
battery is with excellent cycle life;
● GEL electrolyte has huge thermal capacity, thermal runaway
phenomena never occur;
● High strength ABS material for container & lid;
● Wide temperature scope of application(-15~45℃).
● Best temperature of application(20±5℃);
● No leaking, safe and reliable;
● Standing or lying down for using, convenient to transport and
● Low self-discharge rate
|Using Mode||Charging Voltage||Temperature Compensation||Max Charging Current|
|Standby Use||2.275±0.025V/cell (25℃)||-3.3mV/℃/cell||30A|
|Cyclic Use||2.45±0.05V/cell (25℃)||-5mV/℃/cell|
● Batteries should be stored in dry and clean warehouse which has
good air exchange system. Batteries should avoid direct sunlight.
Batteries should not be near to heat (such as radiator, the
distance should more than 1m). Batteries should avoid any toxic gas
and organic solvent.
● When the ambient temperature is less than 25℃, the longest
storage life is 6 months. If ambient temperature is higher, the
longest storage life varies as specified in below chart.
|Storage Temperature (℃)||≤25||26～33||34～40|
|Storage Time (Month)||6||3||1|
●Batteries should be recharged within the storage life or before
Charging methods: maximum charging current 30A, constant voltage
Charging time: 15~20h; Temperature compensation coefficient:
● UPS & EPS system
● Electric power
● Solar/wind system
• Sealed Construction
The unique construction and sealing techniques of the battery
guarantee leak proof operation in any position with no adverse
effect to capacity or service life.
• Electrolyte Suspension System
All batteries utilize an electrolyte suspension system consisting
of a high porosity, glass fiber material which in conjunction with
plates, totally absorb and contain the electrolyte.
• Gas Recombination
CGB batteries incorporate a built-in design that controls gas
generation and induces recombination of more than 99% of gases
generated during float or cyclic usage.
• Maintenance Free Operation
There is no need to check specific gravity of the electrolyte or
add water to batteries during float service life. In fact, there is
no provision for this type of maintenance.
• Low Pressure Valve Regulated System..
All batteries are equipped with safety release valves, designed to
operate between 1.5 and 6 psi (10-40kPa) and automatically reseal.
Hence, there is never an excessive accumulation of gas within the
• Heavy Duty Grids
Heavy duty lead calcium tin alloy grids provide an extra margin of
performance and service life in either float or cyclic
• Cyclic Service Life
More that 600 discharge/recharge cycles can be realized from CGB CB
and HR batteries, dependent on the average depth of discharge.
• Float Service Life
CB, HR and SE Series batteries have an expected life span of 3 to 5
years in float service applications.
• Self Discharge - Shelf Life
The self discharge rate at room temperature is approximately 3% of
rated capacity per month.
• Operating Temperature
CGB Batteries may be operated over a broad range of ambient
• Deep Discharge Recovery
The batteries recover their capacities even after repeated deep
What's the quality assurance we can provide and how do we control
1. Established a procedure to check product at all stages of the
manufacturing process - raw material, in process material,
validated or tested material, finished goods, etc. Besides, we have
also developed a procedure which identifies the inspection and test
status of all items at all stages of the manufacturing process.
2. 100% inspection on assembly lines. All controls, inspections,
equipment, fixtures, total production resources and skills are
inspected to confirm they consistently achieve the required quality
Can we change the color based on the original?
Yes, the color can be customer-made according to your requirement.
Can you print my picture or logo on the battery cover?
Yes, OEM is available,we can print your picture or logo on the
battery case, and you can offer your logo.
What kind of guarantee you give?
Our warranty time is 18 months. If it has quality problem during
the warranty time we will change new battery for you.